Wire Coil-Freening Runed Threaded Insert Technical Parameters - Knowledge Industry

W dan d1 adalah nilai kawalan untuk memasukkan thread (Running Percuma) sebelum dipasang.

Panjang hanya boleh diukur untuk memasukkan sisipan thread.

gambar

d = diameter thread nominal

P = Pitch Thread

d1 = Diameter luar sisipan benang sebelum pemasangan

W = Bilangan benang sebelum pemasangan

DHC = Diameter luar benang induk

D1HC = diameter puncak

B = diameter gerudi twist yang sesuai. Sila ambil perhatian:

D1HC adalah kritikal untuk memilih diameter gerudi twist yang betul

t1 = Kedalaman minimum lubang yang ditoreh

t2 = Panjang nominal memasukkan thread sesuai dengan panjang minimum benang induk penuh untuk buta

lubang atau ketebalan plat minimum untuk lubang melalui

t3 = Kelebihan skru maksimum apabila tang tidak dikeluarkan

t5 = Jarak sisipan thread dari muka bersama = 0.25 hingga 0.5 P, jika t2 sepadan dengan yang disebutkan di atas

nilai minimum

Parameter Teknikal - Metrik

dx p	xd	L (mm)	W	d1 min.max (mm)	B (mm)
M1.6x0.35	1d	1.6	3.1	2.1 ~ 2.3	1.6
	1.5d	2.4	4.5
	2d	3.2	6.2
M2x0.4	1d	2	3.2	2.5 ~ 2.8	2.1
	1.5d	3	5.3
	2d	4	7.4
	2.5d	5	9.5
	3d	6	11.6
M2.5x0.45	1d	2	3.6	3.3 ~ 3.5	2.6
	1.5d	3.8	5.9
	2d	5	8.2
	2.5d	6.3	10.5
	3d	7.5	12.8
M3x0.5	1d	3	4.2	3.8 ~ 4	3.1
	1.5d	4.5	6.8
	2d	6	9.4
	2.5d	7.5	12
	3d	9	14.6
M3.5x0.6	1d	3.5	4	4.55 ~ 4.75	3.7
	1.5d	5.3	6.4
	2d	7	8.9
	2.5d	8.8	11.4
	3d	10.5	13.9
M4x0.7	1d	4	4	5.05 ~ 5.25	4.2
	1.5d	6	6.6
	2d	8	9.1
	2.5d	10	11.7
	3d	12	14.2
M5x0.8	1d	5	4.4	6.35 ~ 6.6	5.2
	1.5d	7.5	7.1
	2d	10	9.9
	2.5d	12.5	12.6
	3d	15	15.3
M6x1	1d	6	4.3	7.6 ~ 7.85	6.3
	1.5d	9	6.9
	2d	12	9.6
	2.5d	15	12.2
	3d	18	14.9
M7x1	1d	7	5.2	8.65 ~ 8.9	7.3
	1.5d	10.5	8.3
	2d	14	11.5
	2.5d	17.5	14.6
M8x1.25	1d	8	4.8	9.85 ~ 10.1	8.3
	1.5d	12	7.7
	2d	16	10.6
	2.5d	20	13.5
	3d	24	16.5
M8x1	1d	8	6	9.85 ~ 10.1	8.3
	1.5d	12	9.6
	2d	16	13.1
	2.5d	20	16.7
M10x1.5	1d	10	5	12.1 ~ 12.5	10.4
	1.5d	15	8.1
	2d	20	11.2
	2.5d	25	14.2
	3d	30	17.3
M10x1.25	1d	10	6.1	12.1 ~ 12.5	10.3
	1.5d	15	9.7
	2d	20	13.3
	2.5d	25	16.9
M10x1	1d	10	7.7	12.0 ~ 12.5	10.3
	1.5d	15	12.1
	2d	20	16.5
	2.5d	25	20.8
M11x1.5	1d	11	5.7	13.0 ~ 13.4	11.4
	1.5d	16.5	9.1
	2d	22	12.5
M12x1.75	1d	12	5.3	14.3 ~ 14.8	12.4
	1.5d	18	8.4
	2d	24	11.6
	2.5d	30	14.8
	3d	36	18
M12x1.5	1d	12	6.2	14.3 ~ 14.8	12.4
	1.5d	18	9.8
	2d	24	13.5
	2.5d	30	17.1
M12x1.25	1d	12	7.5	14.3 ~ 14.8	12.3
	1.5d	18	11.8
	2d	24	16.1
	2.5d	30	20.3
M12x1	1d	12	9.4	14.3 ~ 14.8	12.3
	1.5d	18	14.7
	2d	24	19.9
M14x2	1d	14	5.4	16.7 ~ 17.2	14.5
	1.5d	21	8.7
	2d	28	11.9
	2.5d	35	15.2
	3d	42	18.4
M14x1.5	0.75d	10.5	5.2	16.7 ~ 17.2	14.4
	1d	14	7.3
	1.5d	21	11.5
	2d	28	15.7
	2.5d	35	19.9
M14x1.25	1d	14	8.8	16.7 ~ 17.2	14.3
M14x1.25	1.5d	21	13.8	16.7 ~ 17.2	14.3
M 16x2	1d	16	6.3	18.8 ~ 19.4	16.5
	1.5d	24	10
	2d	32	13.7
	2.5d	40	17.5
	3d	48	21.2
M16x1.5	0.75d	12	6.1	18.8 ~ 19.4	16.4
	1d	16	8.5
	1.5d	24	13.3
	2d	32	18.1
M18x2.5	1d	18	5.6	21.4 ~ 22	18.6
	1.5d	27	9
	2d	36	12.3
	2.5d	45	15.7
	3d	54	19
M18x2	0.75d	13.5	5	21.4 ~ 22	18.5
	1d	18	7.1
	1.5d	27	11.2
	2d	36	15.2
M18x1.5	0.75d	13.5	7.1	21.4 ~ 22	18.4
	1d	18	9.8
	1.5d	27	15
	2d	36	20.3
M20x2.5	1d	20	6.5	23.6 ~ 24.2	20.6
	1.5d	30	10
	2d	40	13.8
	2.5d	50	17.5
	3d	60	21.2
M20x2	0.75d	15	5.7	23.6 ~ 24.2	20.5
	1d	20	8
	1.5d	30	12.5
	2d	40	17.1
M20x1.5	0.5d	10	4.8	23.6 ~ 24.2	20.4
	0.75d	15	7.8
	1d	20	10.7
	1.5d	30	16.7
M22x2.5	1d	22	6.9	26.2 ~ 26.8	22.6
	1.5d	33	11
	2d	44	15
	2.5d	55	19
	3d	66	23
M 22x2	0.75d	16.5	6.3	26.2 ~ 26.8	22.5
	1d	22	8.8
	1.5d	33	13.7
	2d	44	18.6
M22x1.5	0.5d	11	5.4	26.2 ~ 26.8	22.4
	0.75d	16.5	8.7
	1d	22	11.9
	1.5d	33	18.4
M 24x3	1d	24	6.3	28.5 ~ 29.1	24.8
	1.5d	36	10
	2d	48	13.7
	2.5d	60	17.5
	3d	72	21.2
M24x2	0.75d	18	7	28.5 ~ 29.1	24.5
	1d	24	9.6
	1.5d	36	15
	2d	48	20.3
M 24x1.5	0.5d	12	6	28.4 ~ 28.9	24.4
	0.75d	18	9.5
	1d	24	13
	1.5d	36	20
M26x1.5	0.5d	13	6.5	28.5 ~ 30	26.4
	0.75d	19.5	10.3
	1d	26	14
M27x3	1d	27	7.2	32.1 ~ 32.5	27.8
	1.5d	40.5	11.3
	2d	54	15.4
	2.5d	67.5	19.5
M27x2	0.75d	20.3	7.9	32.1 ~ 32.2	27.5
	1d	27	10.9
	1.5d	40.5	16.9
M27x1.5	0.5d	13.5	6.9	31.3 ~ 32.1	27.4
	0.75d	20.3	10.9
	1d	27	14.9
	1.5d	40.5	22.8
M28x1.5	0.5d	14	7.1	33.0 ~ 33.6	28.4
	0.75d	21	11.2
	1d	28	15.3
	1.5d	42	23.5
M30x3.5	1d	30	6.9	35.0 ~ 35.6	30.9
	1.5d	45	11
	2d	60	15
	2.5d	75	19
M30x2	0.5d	15	5.6	34.7 ~ 35.3	30.5
	0.75d	22.5	9
	1d	30	12.3
	1.5d	45	19
M30x1.5	0.5d	15	7.8	34.3 ~ 34.9	30.4
	0.75d	22.5	12.2
	1d	30	16.7
	1.5d	45	25.5
M33x3.5	1d	33	7.8	38.1 ~ 38.6	33.9
	1.5d	49.5	12.2
	2d	66	16.6
	2.5d	82.5	21.1
	3d	99	25.5
M33x2	0.5d	16.5	6.4	38.0 ~ 38.5	33.5
	0.75d	24.8	10.1
	1d	33	13.8
	1.5d	49.5	21.2
M33x1.5	0.5d	16.5	8.7	37.8 ~ 38.3	33.4
	0.75d	24.8	13.6
	1d	33	18.5
M36x4	0.75d	27	5.2	41.9 ~ 42.3	37
	1d	36	3.7
	1.5d	54	11.6
	2d	72	15.8
M36x3	0.5d	18	4.4	41.8 ~ 42.3	36.8
	0.75d	27	7.1
	1d	36	9.9
	1.5d	54	15.4
M36x2	0.5d	18	6.9	41.7 ~ 42.3	36.5
	0.75d	27	11
	1d	36	15
	1.5d	54	23
M39x2	0.5d	19.5	7.7	44.8 ~ 45.4	39.5
	0.75d	29.3	12.1
	1d	39	16.4
M42x4.5	1d	42	7.3	49 ~ 51	43
	1.25d	52	9.5
	1.5d	63	11.6
M42x3.0	1d	42	11.7	48 ~ 50.5	43
	1.25d	52	14.8
	1.5d	63	18.1
M48x3	0.5d	24	6.2	55 ~ 55.5	48.8
	0.75d	36	9.9
	1d	48	13.6
M56x4	0.5d	28	5.4	64 ~ 65	17
	0.75d	42	8.6
	1d	56	11.8
M60x3	0.5d	30	7.9	69 ~ 70	60.8
	0.75d	45	12.4
	1d	60	16.9
	1.5d	90	25.9
M60x4	0.5d	30	5.8	69 ~ 70	61
	0.75d	45	9.2
	1d	60	12.6
	1.5d	90	19.5

Parameter Teknikal - UNC / UNF

d nombor-benang	d	p	xd	L (mm)	W	d1 min.max (mm)	B (mm)
2-56	2.184	0.45	1d	2.18	3.3	2.7-3.1	2.3
			1.5d	3.28	5
			2d	4.37	6.8
4-40	2.845	0.64	1d	2.90	3.2	3.6-4.0	3.0
			1.5d	4.30	5.1
			2d	5.80	7.2
5-40	3.175	0.64	1d	3.20	3.7	4.0-4.4	3.3
			1.5d	4.80	5.9
			2d	6.40	8.2
6-32	3.505	0.79	1d	3.50	2.8	4.5-4.9	3.7
			1.5d	5.30	4.8
			2d	7.00	6.8
8-32	4.166	0.79	1d	4.20	4	5.2-5.6	4.4
			1.5d	6.25	6
			2d	8.30	8.7
8-36	4.166	0.71	1d	4.20	4.5	5.1-5.6	4.3
			1.5d	6.30	7.2
			2d	8.30	9.7
10-24	4.826	1.06	1d	4.80	3.3	6.1-6.6	5.1
			1.5d	7.20	5.4
			2d	9.60	7.5
10-32	4.826	0.79	1d	4.83	4.3	5.9-6.5	5.0
			1.5d	7.24	6.9
			2d	9.60	9.5
12-24	5.486	1.06	1d	5.50	4	6.8-7.2	5.8
			1.5d	8.20	6.3
			2d	11.00	8.8
1/4 '' - 20	6.35	1.27	1d	6.40	3.9	7.8-8.3	6.7
			1.5d	9.50	6.2
			2d	12.70	8.6
1/4 '' - 28	6.35	0.91	1d	6.35	5.3	7.7-8.3	6.6
			1.5d	9.50	8.6
			2d	12.70	11.8
5/16 '' - 18	7.938	1.41	1d	7.90	4.3	9.6-10.2	8.3
			1.5d	11.90	6.8
			2d	15.90	9.4
5/16 '' - 24	7.938	1.06	1d	7.90	5.9	9.6-10.2	8.2
			1.5d	11.90	9.4
			2d	15.90	12.8
3/18 '' - 16	9.525	1.59	1d	9.50	4.8	11.4-11.9	9.9
			1.5d	14.30	7.7
			2d	19.10	10.6
3/8 '' - 24	9.525	1.06	1d	9.50	7.3	11.4-11.9	9.8
			1.5d	14.30	11.5
			2d	19.10	15.6
7/16 '' - 14	11.113	1.81	1d	11.10	4.9	13.3-13.9	11.6
			1.5d	16.70	7.9
			2d	22.20	10.7
7/16 '' - 20	11.113	1.27	1d	11.10	7	13.3-13.7	11.4
			1.5d	16.70	11.1
			2d	22.20	15
1/12 '' - 13	12.7	1.95	1d	12.70	5.2	15.1-15.7	13.2
			1.5d	19.10	8.3
			2d	25.40	11.4
1/12 '' - 20	12.7	1.27	1d	12.70	7.9	15-15.6	13.0
			1.5d	19.10	12.8
			2d	25.40	17.3
9/16 '' - 18	14.288	1.41	1d	14.30	7.9	16.91-17.55	14.6
			1.5d	21.50	12
			2d	28.60	16
5/8 '' - 11	15.875	2.31	1d	15.9	5.7	18.8-19.4	16.5
			1.5d	23.8	9
			2d	31.8	12.3
5/8 '' - 18	15.875	1.41	1d	15.9	9.4	18.6-19.3	16.2
			1.5d	23.8	14.5
			2d	31.8	19.7
3/4 '' - 10	19.05	2.54	1d	19.1	6.3	22.3-23.0	19.7
			1.5d	28.6	9.9
			2d	38.1	13.5
3/4 '' - 16	19.05	1.59	1d	19.1	10.1	22.2-22.8	19.4
			1.5d	28.6	15.6
			2d	38.1	21
7/8 '' - 14	22.225	1.81	1d	22.2	10.3	25.9-26.7	22.6
			1.5d	33.3	15.9
			2d	44.5	21.6
1/8 '' - 14	25.4	3.18	1d	25.4	6.8	29.6-30.4	26.1
			1.5d	38.1	10.6
			2d	50.8	15.4
1 '' - 12	25.4	2.12	1d	25.4	10	29.6-30.4	30.0
			1.5d	38.1	15.6
			2d	25.4	11.8
1 '' - 14	25.4	1.81	1d	25.4	11.8	29.6-30.4	25.9
			1.5d	38.1	18.1
			2d	50.8	24.5

Wire Coil-Running Terperangkap Threaded Masukkan Parameter Teknikal